Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
I saw in the March 2019 Vol36,No.1 Iss 259. I have 2 Christian people very close to me that could likely be getting married soon . When I saw the unity cross on page one this would be the perfect gift from a parent. I would like to make it but need the plans. I do not need 3,000 or 60,000 plans I just wish to purchase the plans for the unity cross. I am a beginner so I need detail plans. Please send me information on ordering just the unity cross plans and where to purchase giant Sequoia and white oak woods. Thank you in advance for your help. I need the plans and information before April.
Another wooden item that I love very much is a beautiful mobile holder. You can see one in the image below. These things are not only beautiful, but they can comfortably hold any sized mobile and ensure proper safety. Another amazing thing is that they can be built in many shapes and sizes, as and how you need it. You can see some more examples at the source below
DoItYourself.com®, founded in 1995, is the leading independent home improvement and repair website. We welcome your comments and suggestions. All information is provided "AS IS." Website operating problems contact [email protected] Questions of a Do It Yourself nature should be submitted to our "DoItYourself.com Community Forums". Copyright© 1995-2018 MH Sub I, LLC dba Internet Brands. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here.
Sanding curves is tricky. Sometimes you need a sanding pad that’s both firm and flexible. A small notepad works great. Just wrap sandpaper around the pad and bend the pad to whatever arc you need. Slip the one end of the sandpaper between the pages to help hold it in place on the pad. Give this a try the next time you’re working on a project that has curves and tough to reach spots.

Despite the abundance of plastics, metals, and other materials, wood products continue to be an important part of our daily lives. Woodworkers make wood products from lumber and synthetic wood materials. Many of these products, including most furniture, kitchen cabinets, and musical instruments, are mass produced. Other products are custom made from architectural designs and drawings.
The shelf in the first picture is made of red oak plywood. You can choose the wood type, color and design as you like for your project. In case if you need more help understanding this project, you can refer the source link below. It discusses various items used, steps and tips and personal experience of the author who personally built a Zigzag shelf.
I mix a lot of epoxy in small batches, but I’ve seldom had the right size container on hand. I solved this problem by drilling 1-1/2-in. holes in 2×4 scraps with a Forstner bit. The resulting shallow “cups” allow easy mixing without the risk of spilling. When the holes are used up, I just make a new mixing board. — Bill Wells. Save your takeout utensils to use in the shop!
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
Finally, properly preparing your wood surface is super important. It will make a huge difference when it comes times to stain, paint, or finish your wood. There are a lot of tips for wood surface preparation, but sanding the wood is one of the most important steps. And I find it really helpful to do the bulk of my sanding before I start ripping (cutting) and building with my wood since it’s still in whole pieces. You can check out my simple tips for how to sand wood in my how to stain wood tutorial, which is also good to reference if you need to learn how to stain too!

Having swing in your own home, yard or garden can be so de-stressing and be relaxing a thing to enjoy, that doesn’t matter you have a big yard or patio, or vacant porch. Kids will surely fall in love with this swing porch and love playing on a breezy day. Even, adults also do relax and enjoy a quite morning coffee, or just being embraced by the sun in the swing.
Cutting sandpaper is a quick way to dull your scissors or utility knife blade. Instead, I fastened a hacksaw blade to the edge of my workbench. I slipped a washer behind the blade at each of the mounting holes so a sheet of sandpaper to easily slides in behind the blade. I fold the paper where I want to cut, just as a reference. — Kim Boley. Try some of these storage solutions!
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
×