This simple jig makes laying out circles a breeze. Drill a 1/8-in. hole through every inch mark on a ruler or yard-stick. To draw a circle, place a pin through the number “1” into the center of your board. Add 1 in. to the radius of the circle you wish to draw, and insert a pencil into this number. Using the pin as a pivot, rotate the pencil to mark the circle. — Edwin Constantino. How to Cut Curves in Wood
There are a few things particleboard is NOT. It’s not medium density fiberboard (MDF)—a material with greater density and weight composed of more uniform particles. It’s NOT oriented strand board (OSB), a material composed of large wood chips and strands that’s structurally equivalent to plywood. It does NOT have great nail or screw holding ability, nor is it all that water resistant; water can quickly cause the material to swell and lose structural integrity. But if you need something flat and cheap for use in a dry place, particleboard will do you proud. Learn how to make a plastic laminate tabletop with a particleboard substrate. 

I mix a lot of epoxy in small batches, but I’ve seldom had the right size container on hand. I solved this problem by drilling 1-1/2-in. holes in 2×4 scraps with a Forstner bit. The resulting shallow “cups” allow easy mixing without the risk of spilling. When the holes are used up, I just make a new mixing board. — Bill Wells. Save your takeout utensils to use in the shop!
Not long ago, I needed to make some angled wood parts to build a new soffit on my garage. I didn’t have the customary tool for the job, but I had some steel joining plates. I screwed through one of the holes in the plate, set my angle, then added another screw to lock the angle. I could then use it as a template to mark all the pieces at the same angle and cut them with my circular saw. — Ryan Bartsch
This particular tray is made using reclaimed barn wood but the author of the project Beyond The Picket Fence surprised everyone with one fact: reclaimed barn wood has often some areas turned pink due to cow urine. If you check the project more closely, you’ll also notice some areas of the tray being almost bright pink. That’s something you don’t see every day!
Finding affordable lumber has always been a mainstay for woodworkers, and when you tie our dwindling natural resources into the conversation the time is right to look at milling your own lumber. This seven-part weekly video series takes you through how to find lumber, how to operate a sawmill, details on types of sawing methods, stickering and drying and ultimately advice on using a mill as part of a business. Learn what you need to know to understand Milling Your Own Lumber.
Not happy with the selection of sanding blocks at the hardware store, I made a few of my own from hardwood scraps left over from a woodworking project. I cut each one to 3/4 in. x 1-1/2 in. x 4-1/2 in.—which is just the right size to wrap a quarter sheet of sandpaper around. And the “kerf” cut helps hold the sandpaper in place until I’m ready to change it. —Tim Olaerts. Here are 41 more genius sanding tips you need to know.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
Often times at first glance a board looks straight and the fact that it is actually bowed or has some warping isn’t always obvious. So the trick to knowing for sure, is to hold the board up towards your face, with the other end on the ground, and look at it at a downward angle (as shown in the below photo). This method will allow you to see if it is bowing at all. 

Pocket screws create a solid, simple-to-make joint. Because of the size and visibility of the hole, it’s usually located in areas that are concealed or rarely seen (though special plugs can be used to fill the holes.) Craig Sommerfeld, founder of The Kreg Tool Company, is credited with popularizing pocket screw joinery in the 1980s. The company today is the leader in creating the jigs, clamps and screws used to create pocket screw joints. Learn how to use a pocket screw jig in woodworking projects.

Finally, properly preparing your wood surface is super important. It will make a huge difference when it comes times to stain, paint, or finish your wood. There are a lot of tips for wood surface preparation, but sanding the wood is one of the most important steps. And I find it really helpful to do the bulk of my sanding before I start ripping (cutting) and building with my wood since it’s still in whole pieces. You can check out my simple tips for how to sand wood in my how to stain wood tutorial, which is also good to reference if you need to learn how to stain too!
When you are gathering inspiration for barn door Plan, be sure to note the cost of the tools used in the plan. Barn door tools can often cost more than your actual door! But, there are many clever and affordable do it yourself tools options in the tutorials mentioned below! Let us explore some DIY Barn Door Tutorials. Just click on the blue text below and check some amazing fun Barn doors. They might be different from the one shown in above picture.
Fir, also known as Douglas Fir, is very inexpensive and common at local home centers. It has a characteristic straight, pronounced grain with a red-brown tint. However, its grain pattern is relatively plain and it does not stain well, so Fir is commonly used when the finished product will be painted. While commonly used for building, this softwood would also be suitable for furniture-making as well.[12]
I use binder clips for a lot of things around the shop, and here’s one that I thought I’d share. When I need to make multiple cuts all the same length, I just clamp my jumbo binder clip to my fence and use a 1/4-in.-thick wood scrap pinched in the clip as a stop. Works like a charm! When it’s not in use, I clamp it to the cord so it’s always nearby. — John Muchow
Pocket screws create a solid, simple-to-make joint. Because of the size and visibility of the hole, it’s usually located in areas that are concealed or rarely seen (though special plugs can be used to fill the holes.) Craig Sommerfeld, founder of The Kreg Tool Company, is credited with popularizing pocket screw joinery in the 1980s. The company today is the leader in creating the jigs, clamps and screws used to create pocket screw joints. Learn how to use a pocket screw jig in woodworking projects.
Occupational employment projections are developed for all states by Labor Market Information (LMI) or individual state Employment Projections offices. All state projections data are available at www.projectionscentral.com. Information on this site allows projected employment growth for an occupation to be compared among states or to be compared within one state. In addition, states may produce projections for areas; there are links to each state’s websites where these data may be retrieved.
Tired of waiting for finish to dry on one side before finishing the other side? You can purchase standoffs, but it’s also really easy to make them yourself. Simply drive 2-in. drywall screws through 2-in. x 2-in. squares of 3/4-in. thick stock. The screw points will leave a divot in the finish that can be touched up later, but I always let the back side of my project rest on the screws while the finish dries. — Matt Boley. Plus: Check out these 32 other handy hints for frugal shop rats.
Tired of waiting for finish to dry on one side before finishing the other side? You can purchase standoffs, but it’s also really easy to make them yourself. Simply drive 2-in. drywall screws through 2-in. x 2-in. squares of 3/4-in. thick stock. The screw points will leave a divot in the finish that can be touched up later, but I always let the back side of my project rest on the screws while the finish dries. — Matt Boley. Plus: Check out these 32 other handy hints for frugal shop rats.
Always nice to see project ideas. Yet, to make a living while woodworking all projects need to be scaled up so that one can actually earn enough to survive and compete against the flood of Chinese imports and others. Substitute products made from plastic, metal or wood are a common place and normally cheaper due to mass production and human rights violations. Politicians don’t care about the disappearance of many of America’s Cottage Industries and most consumers don’t care as well.
It is one of the easiest woodwork projects we are going to discuss today. Although it looks very easy to make, I still could not find any good tutorial on the internet that explains how to build this one. So I am here sharing an article link that gets the closest. The article explains how to make different kinds of DIY candle holders and what items you may need for the project. 

Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
Examples of Bronze Age wood-carving include tree trunks worked into coffins from northern Germany and Denmark and wooden folding-chairs. The site of Fellbach-Schmieden in Germany has provided fine examples of wooden animal statues from the Iron Age. Wooden idols from the La Tène period are known from a sanctuary at the source of the Seine in France.
These things may be tiny in size, but building one is not that easy. It takes some serious woodworking knowledge and skill to build a nice wooden mobile stand. When I first saw one online, I just couldn’t resist thinking of buying one. But when I saw the price, I was forced to rethink. Also, a woodwork lover like me cannot be contained with just one piece and I was not willing to spend on more than one. So instead I decided to build myself one. Yes, it took some doing but the final result was satisfying. Luckily, I found this awesome tutorial online that helped me build my first ever wooden phone holder.
The progenitors of Chinese woodworking are considered to be Lu Ban (魯班) and his wife Lady Yun, from the Spring and Autumn period (771 to 476 BC). Lu Ban is said to have introduced the plane, chalk-line, and other tools to China. His teachings were supposedly left behind in the book Lu Ban Jing (魯班經, "Manuscript of Lu Ban"). Despite this, it is believed that the text was written some 1500 years after his death. This book is filled largely with descriptions of dimensions for use in building various items such as flower pots, tables, altars, etc., and also contains extensive instructions concerning Feng Shui. It mentions almost nothing of the intricate glue-less and nail-less joinery for which Chinese furniture was so famous.
Turning an old door into a photo frame is another easy woodwork project. All you need is an old door and some woodworking tools and items. I am here sharing the link to the source tutorial that explains the step by step procedure for building a picture frame from an old wooden door. This tutorial was originally written by Tracy Snyder at athomewithsweett.blogspot.com who also tells you what items you may need and where to find them. If you haven’t already got an old door, you can purchase one from websites like Craigslist.
Finding a toolbox for a mechanic, for his hand tools, is not a big challenge at all - there are dozens of the tool boxes available on the market, from huge roll-around shop cases to small metal boxes. Plumbers, electricians, and farmers are well served, too, with everything from pickup-truck storage to toolboxes and belts. But, if you are a shop-bound woodworker then the case changes. You get to need a tool box that suits the range and variety of hand tools that most woodworkers like to have. For those who deny making do with second best, there's only one solution, you’ve to build a wooden toolbox that should be designed expressly for a woodworking shop.

Some tools that are required for this project are Miter saw, drilling machine, pencil, tape measure, screws, etc. Those, who prefer a video tutorial instead, can visit the below link to a YouTube video tutorial that illustrates the process of creating a DIY Beer Bottle Crate. The video tutorial explains every step properly so that anyone can make a Beer bottle crate easily.
A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.
For many of us, the moment we learned that a 2×4 board is actually 1.5 inches x 3.5 inches was simply mind-blowing. The reason for this apparent contradiction is that the board has been planed down to eliminate irregularities. At one point, many years ago, 2x4s actually were 2 inches x 4 inches, but their rough surfaces made them difficult to stock and handle. The old terms, such as 2×4 or 4×4, are still used, and are known as the “nominal” size of the board. These nominal sizes are used because they are easier to say and they stick to tradition. Now, thanks to a lawsuit, most big box stores list the nominal and actual sizes of lumber.
Here’s an easier way to stain or seal chairs, lattice or anything with numerous tight recesses. Pour the stain into a clean, empty spray bottle ($3). Spray the stain onto the project and wipe up the excess with a brush or rag. The sprayer will squirt stain into all those tight, hard-to-reach cracks and joints. — Valrie Schuster. Learn more about staining wood.
The best thing about the toy chest is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can also modify your kid’s toy chest in any way you want or build in a different design or color different from the one pictured above. You can try some other designs for your plan in the below-mentioned link.
Some tools that are required for this project are Miter saw, drilling machine, pencil, tape measure, screws, etc. Those, who prefer a video tutorial instead, can visit the below link to a YouTube video tutorial that illustrates the process of creating a DIY Beer Bottle Crate. The video tutorial explains every step properly so that anyone can make a Beer bottle crate easily.
See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products
You can also make one for elders and put it in your garden or terrace or anywhere in the house. Elders can use it to relax and kids can use it to play or sleep. Although this is a really beautiful piece of woodwork, it is not that easy to make. Only someone with good woodworking skill can think of making this swing set. Also, I couldn’t find a good tutorial that illustrates the process of building a wooden boat-shaped swing set. Most Probably, I will write one when I build mine.But if you really want this swing set like right now, I would suggest you hire a good woodworker, who can build something similar. Or just search the internet and maybe you get lucky enough to find a tutorial for this. Good luck either way.

Sanding curves is tricky. Sometimes you need a sanding pad that’s both firm and flexible. A small notepad works great. Just wrap sandpaper around the pad and bend the pad to whatever arc you need. Slip the one end of the sandpaper between the pages to help hold it in place on the pad. Give this a try the next time you’re working on a project that has curves and tough to reach spots.

×