This simple jig makes laying out circles a breeze. Drill a 1/8-in. hole through every inch mark on a ruler or yard-stick. To draw a circle, place a pin through the number “1” into the center of your board. Add 1 in. to the radius of the circle you wish to draw, and insert a pencil into this number. Using the pin as a pivot, rotate the pencil to mark the circle. — Edwin Constantino. How to Cut Curves in Wood
Sanding curves is tricky. Sometimes you need a sanding pad that’s both firm and flexible. A small notepad works great. Just wrap sandpaper around the pad and bend the pad to whatever arc you need. Slip the one end of the sandpaper between the pages to help hold it in place on the pad. Give this a try the next time you’re working on a project that has curves and tough to reach spots.
Tired of waiting for finish to dry on one side before finishing the other side? You can purchase standoffs, but it’s also really easy to make them yourself. Simply drive 2-in. drywall screws through 2-in. x 2-in. squares of 3/4-in. thick stock. The screw points will leave a divot in the finish that can be touched up later, but I always let the back side of my project rest on the screws while the finish dries. — Matt Boley. Plus: Check out these 32 other handy hints for frugal shop rats.
When you are gathering inspiration for barn door Plan, be sure to note the cost of the tools used in the plan. Barn door tools can often cost more than your actual door! But, there are many clever and affordable do it yourself tools options in the tutorials mentioned below! Let us explore some DIY Barn Door Tutorials. Just click on the blue text below and check some amazing fun Barn doors. They might be different from the one shown in above picture.
Cutting sandpaper is a quick way to dull your scissors or utility knife blade. Instead, I fastened a hacksaw blade to the edge of my workbench. I slipped a washer behind the blade at each of the mounting holes so a sheet of sandpaper to easily slides in behind the blade. I fold the paper where I want to cut, just as a reference. — Kim Boley. Try some of these storage solutions!
Sanding curves is tricky. Sometimes you need a sanding pad that’s both firm and flexible. A small notepad works great. Just wrap sandpaper around the pad and bend the pad to whatever arc you need. Slip the one end of the sandpaper between the pages to help hold it in place on the pad. Give this a try the next time you’re working on a project that has curves and tough to reach spots.
The best thing about this wine rack is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can modify your wine rack any way you want or build in a design or color different from this one. The basic steps to build a wooden wine rack are the same for all variants. I have included here the video tutorial that I followed in order to build myself a pallet wide rack.
Making a garden arched footbridge out of some wood boards can be fun, hard working plan and also it’s quite rewarding. We are providing the project tutorial for how to build an arched footbridge without rails or having rails. If you take your hands of work and have some basic woodworking skills you can easily build this type of bridge. While this garden bridge is too small to walk over but it can make a really stunning addition to your lush yard or garden.
This rack can be built from old unused wood pallets you can find around the house. So it is also a great way to recycle those old pallets. You can also find a step by step tutorial at instructables.com for which I have included the source link below. This tutorial helps you to make a wood wine rack from the scratch. So what are waiting for? Just grab the items you need and start building a cool wooden rack for those nice wine bottles of yours.
Sanding small items is tricky, as they’re hard to clamp in a vise to work on them. So instead of bringing the sandpaper to the workpiece, I bring the workpiece to the sandpaper. I glue sheets of sandpaper to a piece of plywood; 60 and 100-grit on one side and 150 and 220-grit on the other. Spray adhesive works well for this. Since there’s sandpaper on both sides, my sanding board doesn’t slide around on the bench. Check out these small projects!
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
This self-clamping table saw fence takes only seconds to put on and lets you crank the blade into the fence to create both angled cuts along board edges and extremely thin rip or rabbet cuts. With a hand- or jigsaw, cut pieces from a 1×4, making the inside width of the “L” a hair under the thickness of your saw’s fence. Drill 5/16-in. holes in the L-blocks and plywood fence and join them with two 1/4-in. x 3-in. countersunk machine screws, washers and Wing-Nuts. As always, use extra caution when you’re sawing without a blade guard. Our thanks for this new sawing angle to professional furniture maker George Vondriska. Check out these 16 genius tool hacks you need to know!
Turning an old door into a photo frame is another easy woodwork project. All you need is an old door and some woodworking tools and items. I am here sharing the link to the source tutorial that explains the step by step procedure for building a picture frame from an old wooden door. This tutorial was originally written by Tracy Snyder at athomewithsweett.blogspot.com who also tells you what items you may need and where to find them. If you haven’t already got an old door, you can purchase one from websites like Craigslist.

Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.

As you can see in the image, this shelf goes on both sides of the corner wall. It looks beautiful and can be used to organize books, trophies, pictures frames and many other things. The strength and design of the shelf depends on how properly you build it. First time workers definitely need some guidance to help them with the process. Therefore, I am including this basic video that I found on YouTube that demonstrates the process of making corner wall wooden shelves.


Softwood is most commonly found in the regions of the world with lower temperatures and is typically less durable, lighter in weight, and more vulnerable to pests and fungal attacks in comparison to hardwoods. They typically have a paler color and a more open grain than hardwoods, which contributes to the tendency of felled softwood to shrink and swell as it dries.[9] Softwoods usually have a lower density, around 25-37lb/cu ft, which can compromise its strength.[9] Density, however, does vary within both softwoods and hardwoods depending on the wood's geographical origin and growth rate. However, the lower density of softwoods also allows it to have a greater strength with lighter weight. In the United States, softwoods are typically cheaper and more readily available and accessible.[9] Most softwoods are suitable for general construction, especially framing, trim, and finish work, and carcassing.[10][9]
Some tools required for this project are hole saw, drilling machine, pencil, tape measure, clamps, etc. This tutorial explains every step properly with images so that anyone can make a wooden sofa sleeve easily. Those, who prefer a video tutorial, can visit the below link to a YouTube video that illustrates the process of building a DIY Sofa Sleeve Cupholder.
This particular tray is made using reclaimed barn wood but the author of the project Beyond The Picket Fence surprised everyone with one fact: reclaimed barn wood has often some areas turned pink due to cow urine. If you check the project more closely, you’ll also notice some areas of the tray being almost bright pink. That’s something you don’t see every day!
This is another example of small woodwork projects that require good time and woodworking skills. This item is built using multiple wooden parts. Each part is shaped in a specific design and then all parts are attached together to make the final TV set. I have never tried building this one, mostly because I don’t own an iPhone, but also because making this item is not an easy task. By the way, it works fine with all kinds of phones.
Making an art or a design on a wooden piece is a hectic task and requires good art skills. But there is another much easier way to carve a beautiful art on any wood surface. For this, you will need the image or graphic that you want to transfer, a piece of wood, freezer paper, etc. I, myself have made several such designs. At the source below, you can find a step by step guide for transferring a graphic image to the wood.
Keep in mind, there are no perfect boards, but try to always use the straighter boards and avoid warping boards. Also, Brandon and I have found that when it comes to picking out lumber at Home Depot and Lowes, they tend to stock up on fresh boards a few days before the weekend starts (so Thursday/Friday). And then, on Sundays and Mondays, the boards are usually really picked over and there isn’t a good selection. Just another tip to keep in mind!
A bottle carrier is a bucket like carrier used to carry beer bottles and so. Yes, the same one you must have used to carry your six-pack. Drinker or not, a bottle carrier is a useful item for everyone. It can be used to carry around or store small items around a household. And it is also very easy to build one. I have several of these lying around my house. Also known as wooden beer totes, this is one wood item you will absolutely love to make. It is also super easy to build.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
The Saw Guy - Saw Reviews and DIY Projects Copyright © 2019. Copyright text 2018 by The Saw Guy - Saw Reviews and DIY Projects. TheSawGuy.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Full affiliate disclaimer here

Lacking a jointer? Use reader Court Kites’ awesome tip to create perfectly matched glue joints on wavy or bowed board edges. Lay the boards on a flat surface, then clamp them across the middle with a bar clamp. Lay two 8-in. long by 1-3/4 in. wide scrap boards across each end and screw them in with four 1-1/4 in. long screws, two per board. Keep the screws well away from your future cutting line!
Simply soak a washcloth in water and ring it out a bit so it’s not sopping wet. Put the damp washcloth on the affected area. The water will wick through the wood, and that’s fine. Now, with your iron on its highest setting, place it on the damp washcloth over the affected area, and make small movements back and forth and in circles. Press down firmly and continue until your wash cloth is dry. It won’t take long to evaporate. At this point, the wood fibers are absorbing the water and should expand back to where they were originally. Continue this process and repeat by adding more water until the dents rise up to be flush with the rest of the material.
Building a wine rack is usually a very common beginner's woodworking plan. Creating a wine rack is an easy plan that can most of the time be completed in a day or half, depending on how large and detailed you would like it to be. And the better news is that this free wine rack plan will let you build you a great looking wine rack for much less than it would cost.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
These things may be tiny in size, but building one is not that easy. It takes some serious woodworking knowledge and skill to build a nice wooden mobile stand. When I first saw one online, I just couldn’t resist thinking of buying one. But when I saw the price, I was forced to rethink. Also, a woodwork lover like me cannot be contained with just one piece and I was not willing to spend on more than one. So instead I decided to build myself one. Yes, it took some doing but the final result was satisfying. Luckily, I found this awesome tutorial online that helped me build my first ever wooden phone holder.
Occupational employment projections are developed for all states by Labor Market Information (LMI) or individual state Employment Projections offices. All state projections data are available at www.projectionscentral.com. Information on this site allows projected employment growth for an occupation to be compared among states or to be compared within one state. In addition, states may produce projections for areas; there are links to each state’s websites where these data may be retrieved.
Popular and easy to work with, cherry is in high demand for its reddish-brown color and ease of staining and finishing. Cherry likely won’t be at the local home center, but should be at a lumberyard for a somewhat expensive price.[12] This hardwood is a very common material for furniture, and is resistant to normal wear-and-tear, but it is best for indoor pieces.[13]
This is definitely going to be one of the easiest woodworking projects you’ll be reading about today. So why not just get started? The tutorial link is given below. Just do exactly what they are saying in the tutorial and you will end up making a beautiful wooden doormat just like the one in the image above. They are using pine wood to build this doormat. You can choose any wood material that best suits your budget.
The Saw Guy - Saw Reviews and DIY Projects Copyright © 2019. Copyright text 2018 by The Saw Guy - Saw Reviews and DIY Projects. TheSawGuy.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Full affiliate disclaimer here
Always nice to see project ideas. Yet, to make a living while woodworking all projects need to be scaled up so that one can actually earn enough to survive and compete against the flood of Chinese imports and others. Substitute products made from plastic, metal or wood are a common place and normally cheaper due to mass production and human rights violations. Politicians don’t care about the disappearance of many of America’s Cottage Industries and most consumers don’t care as well.
Here’s a safe and sound way to make long cuts with a circular saw on plywood clamped to a worktable. Cut about 12 in. into the plywood, then twist a piece of duct tape into a bow tie, with up-and-down adhesive faces. Slide it in the saw kerf and press the tape down above and under the plywood. Now as you finish the cut, the trailing end can’t curl down dangerously as you saw. Hats off to Mike Connelly for simplifying this job. Check out how to make this DIY duct tape wallet.
Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.

Some tools that are required for this project are Miter saw, drilling machine, pencil, tape measure, screws, etc. Those, who prefer a video tutorial instead, can visit the below link to a YouTube video tutorial that illustrates the process of creating a DIY Beer Bottle Crate. The video tutorial explains every step properly so that anyone can make a Beer bottle crate easily.
Short scraps of hardwood are too good to throw away but hard to store neatly. So I bought a 4-ft. tube form made for concrete footings, cut it in half (the cardboard-like material cuts easily) and set the tubes on end. I tack the tubes to a wall or a bench leg so they don’t fall over. With the wood scraps stored upright, it’s easy to find a piece just the right length. Tube forms are available in various diameters for $5 and up at home centers. — Bill Wells. Here’s another brilliant use for these concrete forms. 

From the image above it seems that you do not require a big tutorial to help you to build this candle holder. All you need is a wood panel, a hook and some nails/screws and do exactly what you see in the picture. Attach the hook to the wood panel using two screws and then, attach the panel to the wall using more nails or screws. That’s it. I hope this gets the job done.
Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.

See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products
A woodworker's Workbench is a special type of bench designed to hold your work when you are working on a wood project. The main purpose of this table is to keep the woodwork steady and to prevent it from moving. Follow the tutorial below to build yourself a nice workbench suitable for your specific woodworking projects. Make sure to modify the table to fit your specific requirements.

There is significant evidence of advanced woodworking in ancient Egypt.[1] Woodworking is depicted in many extant ancient Egyptian drawings, and a considerable amount of ancient Egyptian furniture (such as stools, chairs, tables, beds, chests) has been preserved. Tombs represent a large collection of these artefacts and the inner coffins found in the tombs were also made of wood. The metal used by the Egyptians for woodworking tools was originally copper and eventually, after 2000 BC bronze as ironworking was unknown until much later.[2]


Cutting sandpaper is a quick way to dull your scissors or utility knife blade. Instead, I fastened a hacksaw blade to the edge of my workbench. I slipped a washer behind the blade at each of the mounting holes so a sheet of sandpaper to easily slides in behind the blade. I fold the paper where I want to cut, just as a reference. — Kim Boley. Try some of these storage solutions!
When it comes to woodworking for beginners, there are 6 things that I think are essential to know for how to start woodworking. I’m going to discuss each of these tips in hopefully a really simple way to make it a breeze to understand, so you can get to the fun part of actually starting to woodwork! I wish when I started and was learning how to woodwork that I had a simple beginner tips guide like this one!
Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.
Finding a toolbox for a mechanic, for his hand tools, is not a big challenge at all - there are dozens of the tool boxes available on the market, from huge roll-around shop cases to small metal boxes. Plumbers, electricians, and farmers are well served, too, with everything from pickup-truck storage to toolboxes and belts. But, if you are a shop-bound woodworker then the case changes. You get to need a tool box that suits the range and variety of hand tools that most woodworkers like to have. For those who deny making do with second best, there's only one solution, you’ve to build a wooden toolbox that should be designed expressly for a woodworking shop.
The best thing about the toy chest is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can also modify your kid’s toy chest in any way you want or build in a different design or color different from the one pictured above. You can try some other designs for your plan in the below-mentioned link.
×