Lacking a jointer? Use reader Court Kites’ awesome tip to create perfectly matched glue joints on wavy or bowed board edges. Lay the boards on a flat surface, then clamp them across the middle with a bar clamp. Lay two 8-in. long by 1-3/4 in. wide scrap boards across each end and screw them in with four 1-1/4 in. long screws, two per board. Keep the screws well away from your future cutting line!
Another important factor to be considered is the durability of the wood, especially in regards to moisture. If the finished project will be exposed to moisture (e.g. outdoor projects) or high humidity or condensation (e.g. in kitchens or bathrooms), then the wood needs to be especially durable in order to prevent rot. Because of their oily qualities, many tropical hardwoods such as teak and mahogany are popular for such applications.[9]

Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.


Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.
Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.
Finally, properly preparing your wood surface is super important. It will make a huge difference when it comes times to stain, paint, or finish your wood. There are a lot of tips for wood surface preparation, but sanding the wood is one of the most important steps. And I find it really helpful to do the bulk of my sanding before I start ripping (cutting) and building with my wood since it’s still in whole pieces. You can check out my simple tips for how to sand wood in my how to stain wood tutorial, which is also good to reference if you need to learn how to stain too!
Sanding concave molding doesn’t have to be difficult. Find a deep socket that fits the contour of your molding. Wrap a piece of sand- paper around the socket and hold it in place with your fingers. Your sanding will be uniform and the delicate edges of the molding won’t round over. — Eric and Cheryl Weltlich. In this video, Travis talks about his favorite sanding tips.
Cutting sandpaper is a quick way to dull your scissors or utility knife blade. Instead, I fastened a hacksaw blade to the edge of my workbench. I slipped a washer behind the blade at each of the mounting holes so a sheet of sandpaper to easily slides in behind the blade. I fold the paper where I want to cut, just as a reference. — Kim Boley. Try some of these storage solutions!
Pocket screws create a solid, simple-to-make joint. Because of the size and visibility of the hole, it’s usually located in areas that are concealed or rarely seen (though special plugs can be used to fill the holes.) Craig Sommerfeld, founder of The Kreg Tool Company, is credited with popularizing pocket screw joinery in the 1980s. The company today is the leader in creating the jigs, clamps and screws used to create pocket screw joints. Learn how to use a pocket screw jig in woodworking projects.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
The best thing about the toy chest is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can also modify your kid’s toy chest in any way you want or build in a different design or color different from the one pictured above. You can try some other designs for your plan in the below-mentioned link.

This is not exactly a tutorial, but a guide to some really cool woodworking projects. Although we are not teaching you to make anything, we are always here to help. Feel free to ask your queries in the comments in case if you face any issue while working on any of these projects. Also, tell us how much you liked this article. Did you enjoy reading it? Did you work on any of these projects, and if yes, how was your experience? You are also welcome to share any images of your completed woodwork projects.


Why would you buy a costly platform bed from Ikea or somewhere else when you can make one yourself at home? Oh yes, you can. A bed is the most common furniture piece used in the house and probably the costliest one. Wouldn’t it be great if you could just make a bed of your own, without having to spend many bucks for buying one? So I am here sharing a great tutorial to help you to build a nice comfy platform bed that you can use anywhere in the house.
Sanding concave molding doesn’t have to be difficult. Find a deep socket that fits the contour of your molding. Wrap a piece of sand- paper around the socket and hold it in place with your fingers. Your sanding will be uniform and the delicate edges of the molding won’t round over. — Eric and Cheryl Weltlich. In this video, Travis talks about his favorite sanding tips.
(function(d,a){function c(){var b=d.createElement("script");b.async=!0;b.type="text/javascript";b.src=a._settings.messengerUrl;b.crossOrigin="anonymous";var c=d.getElementsByTagName("script")[0];c.parentNode.insertBefore(b,c)}window.kayako=a;a.readyQueue=[];a.newEmbedCode=!0;a.ready=function(b){a.readyQueue.push(b)};a._settings={apiUrl:"https://woodworker.kayako.com/api/v1",messengerUrl:"https://woodworker.kayakocdn.com/messenger",realtimeUrl:"wss://kre.kayako.net/socket"};window.attachEvent?window.attachEvent("onload",c):window.addEventListener("load",c,!1)})(document,window.kayako||{});
This is definitely going to be one of the easiest woodworking projects you’ll be reading about today. So why not just get started? The tutorial link is given below. Just do exactly what they are saying in the tutorial and you will end up making a beautiful wooden doormat just like the one in the image above. They are using pine wood to build this doormat. You can choose any wood material that best suits your budget.
Commonly used woodworking tools included axes, adzes, chisels, pull saws, and bow drills. Mortise and tenon joints are attested from the earliest Predynastic period. These joints were strengthened using pegs, dowels and leather or cord lashings. Animal glue came to be used only in the New Kingdom period.[3] Ancient Egyptians invented the art of veneering and used varnishes for finishing, though the composition of these varnishes is unknown. Although different native acacias were used, as was the wood from the local sycamore and tamarisk trees, deforestation in the Nile valley resulted in the need for the importation of wood, notably cedar, but also Aleppo pine, boxwood and oak, starting from the Second Dynasty.[4]
Examples of Bronze Age wood-carving include tree trunks worked into coffins from northern Germany and Denmark and wooden folding-chairs. The site of Fellbach-Schmieden in Germany has provided fine examples of wooden animal statues from the Iron Age. Wooden idols from the La Tène period are known from a sanctuary at the source of the Seine in France.
×