Softwood is most commonly found in the regions of the world with lower temperatures and is typically less durable, lighter in weight, and more vulnerable to pests and fungal attacks in comparison to hardwoods. They typically have a paler color and a more open grain than hardwoods, which contributes to the tendency of felled softwood to shrink and swell as it dries.[9] Softwoods usually have a lower density, around 25-37lb/cu ft, which can compromise its strength.[9] Density, however, does vary within both softwoods and hardwoods depending on the wood's geographical origin and growth rate. However, the lower density of softwoods also allows it to have a greater strength with lighter weight. In the United States, softwoods are typically cheaper and more readily available and accessible.[9] Most softwoods are suitable for general construction, especially framing, trim, and finish work, and carcassing.[10][9]

There is significant evidence of advanced woodworking in ancient Egypt.[1] Woodworking is depicted in many extant ancient Egyptian drawings, and a considerable amount of ancient Egyptian furniture (such as stools, chairs, tables, beds, chests) has been preserved. Tombs represent a large collection of these artefacts and the inner coffins found in the tombs were also made of wood. The metal used by the Egyptians for woodworking tools was originally copper and eventually, after 2000 BC bronze as ironworking was unknown until much later.[2] 

Cutting sandpaper is a quick way to dull your scissors or utility knife blade. Instead, I fastened a hacksaw blade to the edge of my workbench. I slipped a washer behind the blade at each of the mounting holes so a sheet of sandpaper to easily slides in behind the blade. I fold the paper where I want to cut, just as a reference. — Kim Boley. Try some of these storage solutions!
Commonly used woodworking tools included axes, adzes, chisels, pull saws, and bow drills. Mortise and tenon joints are attested from the earliest Predynastic period. These joints were strengthened using pegs, dowels and leather or cord lashings. Animal glue came to be used only in the New Kingdom period.[3] Ancient Egyptians invented the art of veneering and used varnishes for finishing, though the composition of these varnishes is unknown. Although different native acacias were used, as was the wood from the local sycamore and tamarisk trees, deforestation in the Nile valley resulted in the need for the importation of wood, notably cedar, but also Aleppo pine, boxwood and oak, starting from the Second Dynasty.[4] 

Occupational employment projections are developed for all states by Labor Market Information (LMI) or individual state Employment Projections offices. All state projections data are available at www.projectionscentral.com. Information on this site allows projected employment growth for an occupation to be compared among states or to be compared within one state. In addition, states may produce projections for areas; there are links to each state’s websites where these data may be retrieved.
(function(d,a){function c(){var b=d.createElement("script");b.async=!0;b.type="text/javascript";b.src=a._settings.messengerUrl;b.crossOrigin="anonymous";var c=d.getElementsByTagName("script")[0];c.parentNode.insertBefore(b,c)}window.kayako=a;a.readyQueue=[];a.newEmbedCode=!0;a.ready=function(b){a.readyQueue.push(b)};a._settings={apiUrl:"https://woodworker.kayako.com/api/v1",messengerUrl:"https://woodworker.kayakocdn.com/messenger",realtimeUrl:"wss://kre.kayako.net/socket"};window.attachEvent?window.attachEvent("onload",c):window.addEventListener("load",c,!1)})(document,window.kayako||{});
$50 - $100Alaska Dream HouseBathroomBedroomChildren's and Kid's Room Furniture and Toy PlansCraftroomDesk, Desk Systems and Project Table Plansdining roomentry wayFarmhouse Style Furniture PlansIndustrial Style Furniture PlansKids and Toysliving roomModern Style Furniture PlansNursery and BabyofficeRustic Furniture Plansstorage and organizationTeensIntermediateSide and End Table PlansBuffet, Sideboard and Credenza PlansCabinet PlansNightstands
Among early finds of wooden tools are the worked sticks from Kalambo Falls, Clacton-on-Sea and Lehringen. The spears from Schöningen (Germany) provide some of the first examples of wooden hunting gear. Flint tools were used for carving. Since Neolithic times, carved wooden vessels are known, for example, from the Linear Pottery culture wells at Kückhofen and Eythra.
Typically furniture such as tables and chairs is made using solid stock from hardwoods due to its strength and resistance to warping.[10] Additionally, they also have a greater variety of grain patterns and color and take a finish better which allows the woodworker to exercise a great deal of artistic liberty. Hardwoods can be cut more cleanly and leave less residue on sawblades and other woodworking tools.[10] Cabinet/fixture makers employ the use of plywood and other man made panel products. Some furniture, such as the Windsor chair involve green woodworking, shaping with wood while it contains its natural moisture prior to drying.
Another important factor to be considered is the durability of the wood, especially in regards to moisture. If the finished project will be exposed to moisture (e.g. outdoor projects) or high humidity or condensation (e.g. in kitchens or bathrooms), then the wood needs to be especially durable in order to prevent rot. Because of their oily qualities, many tropical hardwoods such as teak and mahogany are popular for such applications.[9]
Making a garden arched footbridge out of some wood boards can be fun, hard working plan and also it’s quite rewarding. We are providing the project tutorial for how to build an arched footbridge without rails or having rails. If you take your hands of work and have some basic woodworking skills you can easily build this type of bridge. While this garden bridge is too small to walk over but it can make a really stunning addition to your lush yard or garden.
If you bought this superb polished table in a store, it would cost you a fortune, but our detailed instructions will help you make one for less than $100. And it looks like highly polished stone, but no-one would know it’s actually made from concrete with a wooden base. Also, you can embellish the top with leaf prints, like the table shown here, or personalize it with glass or mosaic tiles or imprints of seashells.

My planer blasts shavings all over the shop floor. I decided to make my own dust chute from 4-in. PVC sewer pipe (which has thinner walls than regular Schedule 40 pipe) and a couple caps. I cut a slit in the pipe and used a heat gun to soften the plastic. That allowed me to open the slit. (Heating PVC releases fumes; ventilation is critical.) I then drilled holes in the flap and screwed it to the planer housing. Finally, I cut a 2-1/2- in. hole in one of the end caps to accept my shop vacuum hose. Works great! — Luis Arce. Here’s what else you can do with PVC pipe.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
Lacking a jointer? Use reader Court Kites’ awesome tip to create perfectly matched glue joints on wavy or bowed board edges. Lay the boards on a flat surface, then clamp them across the middle with a bar clamp. Lay two 8-in. long by 1-3/4 in. wide scrap boards across each end and screw them in with four 1-1/4 in. long screws, two per board. Keep the screws well away from your future cutting line!
There is significant evidence of advanced woodworking in ancient Egypt.[1] Woodworking is depicted in many extant ancient Egyptian drawings, and a considerable amount of ancient Egyptian furniture (such as stools, chairs, tables, beds, chests) has been preserved. Tombs represent a large collection of these artefacts and the inner coffins found in the tombs were also made of wood. The metal used by the Egyptians for woodworking tools was originally copper and eventually, after 2000 BC bronze as ironworking was unknown until much later.[2]
With the advances in modern technology and the demands of industry, woodwork as a field has changed. The development of Computer Numeric Controlled (CNC) Machines, for example, has made us able to mass-produce and reproduce products faster, with less waste, and often more complex in design than ever before. CNC Routers can carve complicated and highly detailed shapes into flat stock, to create signs or art. Rechargeable power tools speed up creation of many projects and require much less body strength than in the past, for example when boring multiple holes. Skilled fine woodworking, however, remains a craft pursued by many. There remains demand for hand crafted work such as furniture and arts, however with rate and cost of production, the cost for consumers is much higher.

This rack can be built from old unused wood pallets you can find around the house. So it is also a great way to recycle those old pallets. You can also find a step by step tutorial at instructables.com for which I have included the source link below. This tutorial helps you to make a wood wine rack from the scratch. So what are waiting for? Just grab the items you need and start building a cool wooden rack for those nice wine bottles of yours.


Although refrigerators long ago rendered them obsolete, antique oak ice boxes remain popular with collectors, even though they’re expensive and hard to find. This do-it-yourself version is neither: it’s both inexpensive and easy to build. An authentic reproduction of an original, the project is especially popular when used as a bar, but it has many
You can also make one for elders and put it in your garden or terrace or anywhere in the house. Elders can use it to relax and kids can use it to play or sleep. Although this is a really beautiful piece of woodwork, it is not that easy to make. Only someone with good woodworking skill can think of making this swing set. Also, I couldn’t find a good tutorial that illustrates the process of building a wooden boat-shaped swing set. Most Probably, I will write one when I build mine.But if you really want this swing set like right now, I would suggest you hire a good woodworker, who can build something similar. Or just search the internet and maybe you get lucky enough to find a tutorial for this. Good luck either way.
Although the term “woodworker” may evoke the image of a craftsman who uses hand tools to build ornate furniture, the modern woodworking trade is highly technical and relies on advanced equipment and highly skilled operators. Workers use automated machinery, such as computerized numerical control (CNC) machines, to do much of the work with great accuracy.
Finding affordable lumber has always been a mainstay for woodworkers, and when you tie our dwindling natural resources into the conversation the time is right to look at milling your own lumber. This seven-part weekly video series takes you through how to find lumber, how to operate a sawmill, details on types of sawing methods, stickering and drying and ultimately advice on using a mill as part of a business. Learn what you need to know to understand Milling Your Own Lumber.
Furnishing and decorating your patio is not an easy task – but then again, it has to be done! Your patio is obviously one of the most important rooms in your home, as you can easily turn it into your little piece of Heaven, your “safe spot” in your home where you can retreat whenever you want to ignore the world and just spend some time alone all by yourself.
Lacking a jointer? Use reader Court Kites’ awesome tip to create perfectly matched glue joints on wavy or bowed board edges. Lay the boards on a flat surface, then clamp them across the middle with a bar clamp. Lay two 8-in. long by 1-3/4 in. wide scrap boards across each end and screw them in with four 1-1/4 in. long screws, two per board. Keep the screws well away from your future cutting line!

Lacking a jointer? Use reader Court Kites’ awesome tip to create perfectly matched glue joints on wavy or bowed board edges. Lay the boards on a flat surface, then clamp them across the middle with a bar clamp. Lay two 8-in. long by 1-3/4 in. wide scrap boards across each end and screw them in with four 1-1/4 in. long screws, two per board. Keep the screws well away from your future cutting line! 

Here, I am writing about another DIY project that involves the use of an old furniture piece. I think that the idea of reusing and recycling old furniture has got to me. Anyways, I am starting to love it. This project involves using an old door to build a beautiful multi picture frame, as you can see in the image below. This frame looks really wonderful and can be used to hold many pictures at a time.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
The best thing about the toy chest is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can also modify your kid’s toy chest in any way you want or build in a different design or color different from the one pictured above. You can try some other designs for your plan in the below-mentioned link.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
The best thing about this wine rack is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can modify your wine rack any way you want or build in a design or color different from this one. The basic steps to build a wooden wine rack are the same for all variants. I have included here the video tutorial that I followed in order to build myself a pallet wide rack.
Afrormosia Alder Andiroba Anigre Ash Apple Aspen Avodire Balsa Beech Bilinga Birch African Blackwood Australian Blackwood Boxwood Bubinga Camphor Cedrela Cherry Chestnut Cocobolo Cumaru Ebony Elm Eucalyptus Hazel Hickory Hornbeam Idigbo Imbuia Ipê Iroko Jarra Jelutong Lignum vitae Linden (lime, basswood) Merbau Mahogany (American, African) Maple Meranti Oak Padauk Pear Plum Poplar Purpleheart Ovankol Ramin Red Quebracho Rosewood Rubberwood Sapele Teak Totara Utile Walnut Wenge Willow Zebrano
See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products
Wall-mounted or placed on a table or countertop, this handsome display cabinet is the perfect way to share any collection while keeping it clean and protected at the same time. Featuring tempered glass doors and three shelves, the cabinet’s design calls for all straight cuts and straightforward construction techniques (simple cut-outs give the effect of
Here’s an easier way to stain or seal chairs, lattice or anything with numerous tight recesses. Pour the stain into a clean, empty spray bottle ($3). Spray the stain onto the project and wipe up the excess with a brush or rag. The sprayer will squirt stain into all those tight, hard-to-reach cracks and joints. — Valrie Schuster. Learn more about staining wood.
Old doors laid across sawhorses make great temporary workbenches, but they take up a lot of space when you’re not using them. Instead of full-size doors, I use bifold doors with hinges so I can fold them up when I’m done working. They’re also easier to haul around in the pickup for on-the-road jobs. — Harry Steele. Here are 12 more simple workbenches you can build.
From the image above it seems that you do not require a big tutorial to help you to build this candle holder. All you need is a wood panel, a hook and some nails/screws and do exactly what you see in the picture. Attach the hook to the wood panel using two screws and then, attach the panel to the wall using more nails or screws. That’s it. I hope this gets the job done.
There is significant evidence of advanced woodworking in ancient Egypt.[1] Woodworking is depicted in many extant ancient Egyptian drawings, and a considerable amount of ancient Egyptian furniture (such as stools, chairs, tables, beds, chests) has been preserved. Tombs represent a large collection of these artefacts and the inner coffins found in the tombs were also made of wood. The metal used by the Egyptians for woodworking tools was originally copper and eventually, after 2000 BC bronze as ironworking was unknown until much later.[2]
Woodworkers set up, operate, and tend all types of woodworking machines, such as saws, milling machines, drill presses, lathes, shapers, routers, sanders, planers, and wood-fastening machines. Operators set up the equipment, cut and shape wooden parts, and verify dimensions, using a template, caliper, and rule. After the parts are machined, woodworkers add fasteners and adhesives and connect the parts to form an assembled unit. They also install hardware, such as pulls and drawer slides, and fit specialty products for glass, metal trims, electrical components, and stone. Finally, workers sand, stain, and, if necessary, coat the wood product with a sealer or topcoats, such as a lacquer or varnish.
Nightstand table plans have everything you need to create a bedside table to keep every needy thing at reach at night time. This Nigh Stand plan is quite different in design from the most of the other plans. This stand has not only the three regular drawers but also having a hidden drawer that uses a secret locking mechanism to keep contents securely.
The rubber cushion on my old palm sander was wearing thin around the edges. Because of its age, I couldn’t find a replacement pad. As I was drinking my beverage with a foam can cover around it, I realized I could cut the foam to fit the sander and glue it on. I peeled off the old pad, cleaned the metal base and attached the foam with contact cement. Works for clamp-on as well as stick-on sanding squares! You can find can covers at discount and convenience stores. — Allen J. Muldoon
Here’s a nifty tip—with a nifty tip—from faithful reader Don Ayers: Fill snap-capped sports water bottles with glue and stick them upside down in a hunk of 2×6. Now you don’t have to wait for the glue to run into the neck of the bottle, and the cap will control glue flow (and never get lost!). To holster the glue dispensers, cut holes in the base with a spade bit that’s a smidgen larger than the cap’s diameter.

There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.


Iron-on edge-banding is a quick way to cover up an edge on plywood. Trimming the excess, however, is tricky. I’ve tried edge-banding trimmers, but I find the results are unpredictable. With the trimmers I’ve tried, it wasn’t easy to change the direction of the cut to suit the grain direction of the edge-banding. If you’re cutting against the grain, you’re likely to tear out a chunk of your new edge-banding. Instead, I use a wide, sharp chisel. This way, I can read the grain direction and trim accordingly. Angle the chisel slightly and go slow, raising the back corner of the chisel just enough so that it doesn’t dig into the plywood veneer. Smooth the corner with a sanding block after trimming. Check out this amazing edge band veneering project!
For many of us, the moment we learned that a 2×4 board is actually 1.5 inches x 3.5 inches was simply mind-blowing. The reason for this apparent contradiction is that the board has been planed down to eliminate irregularities. At one point, many years ago, 2x4s actually were 2 inches x 4 inches, but their rough surfaces made them difficult to stock and handle. The old terms, such as 2×4 or 4×4, are still used, and are known as the “nominal” size of the board. These nominal sizes are used because they are easier to say and they stick to tradition. Now, thanks to a lawsuit, most big box stores list the nominal and actual sizes of lumber.
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
Another important factor to be considered is the durability of the wood, especially in regards to moisture. If the finished project will be exposed to moisture (e.g. outdoor projects) or high humidity or condensation (e.g. in kitchens or bathrooms), then the wood needs to be especially durable in order to prevent rot. Because of their oily qualities, many tropical hardwoods such as teak and mahogany are popular for such applications.[9]
Turning an old door into a photo frame is another easy woodwork project. All you need is an old door and some woodworking tools and items. I am here sharing the link to the source tutorial that explains the step by step procedure for building a picture frame from an old wooden door. This tutorial was originally written by Tracy Snyder at athomewithsweett.blogspot.com who also tells you what items you may need and where to find them. If you haven’t already got an old door, you can purchase one from websites like Craigslist.
Boat building Bow and arrow Bush carpentry Cabinetry Caning Carpentry Certosina Chainsaw carving Chip carving Clogs Ébéniste Fretwork Intarsia Japanese carpentry Khatam Kohlrosing Log building Marquetry Millwork Parquetry Pyrography Relief carving Root carving Sawdust Segmented turning Shingle weaving Shipbuilding Spindle turning Timber framing Treen Whittling Wood carving Woodturning Wood flour
As you can see in the image, this shelf goes on both sides of the corner wall. It looks beautiful and can be used to organize books, trophies, pictures frames and many other things. The strength and design of the shelf depends on how properly you build it. First time workers definitely need some guidance to help them with the process. Therefore, I am including this basic video that I found on YouTube that demonstrates the process of making corner wall wooden shelves.

See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products
Making an art or a design on a wooden piece is a hectic task and requires good art skills. But there is another much easier way to carve a beautiful art on any wood surface. For this, you will need the image or graphic that you want to transfer, a piece of wood, freezer paper, etc. I, myself have made several such designs. At the source below, you can find a step by step guide for transferring a graphic image to the wood.
×