With an orbital sander and good sandpaper you can smooth wood evenly and easily with first-class results. When flush-sanding solid edge-banding, draw a squiggly line across the joint before sanding. The edge-banding will be slightly proud of the plywood veneer, so the pencil marks provide a visual aid to make sure that you’re sanding flat, and that you don’t sand through the plywood’s veneer. As you go, you can also test for a smooth, level transition by gently scraping your fingernails against the transition. If it’s smooth, your fingers will not catch on the seam between the two pieces

Sanding concave molding doesn’t have to be difficult. Find a deep socket that fits the contour of your molding. Wrap a piece of sand- paper around the socket and hold it in place with your fingers. Your sanding will be uniform and the delicate edges of the molding won’t round over. — Eric and Cheryl Weltlich. In this video, Travis talks about his favorite sanding tips.
Finally, as I shared in my post last week on how I learned woodworking, I learned how to use power tools by watching YouTube videos and then just trying them out for myself. I highly recommend this method to learn how to use your power tools. There are lots of videos on specific models of tools too. So, watch a few how-to videos and very importantly, review the tool manual and safety guide for your own tools. Then, go ahead and try the tool out yourself and start using it!
See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products
“I do a lot of finish-sanding freehand, without a sandpaper block, so I can smooth edges and get into nooks and crannies. But the finer grits are usually bonded to thinner paper and, at least for me, the paper is too thin and ends up tearing long before the grit wears out. So I apply duct tape to the back of the sandpaper. The sandpaper is still flexible enough to sand a tight radius and it’s far more durable. You can use this super-strong sandpaper like a shoeshine rag.” — Chuck Merchant
We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!

As soon as I came across this tutorial, I didn’t wait any longer to start building one. Some of the items you need for this project are hardwood plywood, saw, glue, nails, drilling machine, etc. The video is very easy to follow for anyone with basic woodworking knowledge and experience. The first source link also includes a step by step procedure in plain English for those, who are not comfortable enough with the video tutorial.
Always nice to see project ideas. Yet, to make a living while woodworking all projects need to be scaled up so that one can actually earn enough to survive and compete against the flood of Chinese imports and others. Substitute products made from plastic, metal or wood are a common place and normally cheaper due to mass production and human rights violations. Politicians don’t care about the disappearance of many of America’s Cottage Industries and most consumers don’t care as well.

Sanding concave molding doesn’t have to be difficult. Find a deep socket that fits the contour of your molding. Wrap a piece of sand- paper around the socket and hold it in place with your fingers. Your sanding will be uniform and the delicate edges of the molding won’t round over. — Eric and Cheryl Weltlich. In this video, Travis talks about his favorite sanding tips.


Finally, properly preparing your wood surface is super important. It will make a huge difference when it comes times to stain, paint, or finish your wood. There are a lot of tips for wood surface preparation, but sanding the wood is one of the most important steps. And I find it really helpful to do the bulk of my sanding before I start ripping (cutting) and building with my wood since it’s still in whole pieces. You can check out my simple tips for how to sand wood in my how to stain wood tutorial, which is also good to reference if you need to learn how to stain too!
Sanding curves is tricky. Sometimes you need a sanding pad that’s both firm and flexible. A small notepad works great. Just wrap sandpaper around the pad and bend the pad to whatever arc you need. Slip the one end of the sandpaper between the pages to help hold it in place on the pad. Give this a try the next time you’re working on a project that has curves and tough to reach spots. 

A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.
Sanding curves is tricky. Sometimes you need a sanding pad that’s both firm and flexible. A small notepad works great. Just wrap sandpaper around the pad and bend the pad to whatever arc you need. Slip the one end of the sandpaper between the pages to help hold it in place on the pad. Give this a try the next time you’re working on a project that has curves and tough to reach spots.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.

A woodworker's Workbench is a special type of bench designed to hold your work when you are working on a wood project. The main purpose of this table is to keep the woodwork steady and to prevent it from moving. Follow the tutorial below to build yourself a nice workbench suitable for your specific woodworking projects. Make sure to modify the table to fit your specific requirements.


Old doors laid across sawhorses make great temporary workbenches, but they take up a lot of space when you’re not using them. Instead of full-size doors, I use bifold doors with hinges so I can fold them up when I’m done working. They’re also easier to haul around in the pickup for on-the-road jobs. — Harry Steele. Here are 12 more simple workbenches you can build. 

Some tools required for this project are hole saw, drilling machine, pencil, tape measure, clamps, etc. This tutorial explains every step properly with images so that anyone can make a wooden sofa sleeve easily. Those, who prefer a video tutorial, can visit the below link to a YouTube video that illustrates the process of building a DIY Sofa Sleeve Cupholder. 

There are many factors to consider when deciding what type of wood to use for a project. One of the most important is the workability of the wood: the way in which it responds when worked by hand or tools, the quality of the grain, and how it responds to adhesives and finishes.[9] When the workability of wood is high, it offers a lower resistance when cutting and has a diminished blunting effect on tools.[9] Highly workable wood is easier to manipulate into desired forms. If the wood grain is straight and even, it will be much easier to create strong and durable glued joints. Additionally, it will help protect the wood from splitting when nailed or screwed.[9] Coarse grains require a lengthy process of filing and rubbing down the grain to produce a smooth result.[9]

When you are gathering inspiration for barn door Plan, be sure to note the cost of the tools used in the plan. Barn door tools can often cost more than your actual door! But, there are many clever and affordable do it yourself tools options in the tutorials mentioned below! Let us explore some DIY Barn Door Tutorials. Just click on the blue text below and check some amazing fun Barn doors. They might be different from the one shown in above picture.

As you can see in the image, this shelf goes on both sides of the corner wall. It looks beautiful and can be used to organize books, trophies, pictures frames and many other things. The strength and design of the shelf depends on how properly you build it. First time workers definitely need some guidance to help them with the process. Therefore, I am including this basic video that I found on YouTube that demonstrates the process of making corner wall wooden shelves.


While trying to trace an exact copy of the throat plate for my table saw, I came up with this nifty technique using an ordinary pencil. I just shaved my pencil into a half-pencil by carefully grinding it on my belt sander. The flat edge enables my modified pencil to ride straight up along the edge of the template. It also works great for marking and then shaping inlays for my woodworking projects. — Tim Reese. How to cut circles with a band saw.
Instead of using a container to mix a small amount of epoxy, just make a mixing surface on your workbench using painters tape. Simply lay down strips, overlapping the edges so the epoxy doesn’t get on your bench. When you’re done, peel off the tape and throw it away. This mixing surface will work for more than just epoxy, you can use it for wood glue or any other material you need easy access to while working on a project.

woodworking projects

×