Use whatever image hosting service you like and post the link to /r/woodworking. The key here is it needs to be apparent that you've built the entry, and you follow the photo requirements listed in the contest rules. Submissions of finished photos only will not be accepted for entry. <-- I can't emphasize this enough, you absolutely need more than 2-3 photos for a valid submission. I will no longer accept entries that have albums that go from rough stock to 90% complete in one jump.
Use whatever image hosting service you like and post the link to /r/woodworking. The key here is it needs to be apparent that you've built the entry, and you follow the photo requirements listed in the contest rules. Submissions of finished photos only will not be accepted for entry. <-- I can't emphasize this enough, you absolutely need more than 2-3 photos for a valid submission. I will no longer accept entries that have albums that go from rough stock to 90% complete in one jump.

Tired of waiting for finish to dry on one side before finishing the other side? You can purchase standoffs, but it’s also really easy to make them yourself. Simply drive 2-in. drywall screws through 2-in. x 2-in. squares of 3/4-in. thick stock. The screw points will leave a divot in the finish that can be touched up later, but I always let the back side of my project rest on the screws while the finish dries. — Matt Boley. Plus: Check out these 32 other handy hints for frugal shop rats.
Why would you buy a costly platform bed from Ikea or somewhere else when you can make one yourself at home? Oh yes, you can. A bed is the most common furniture piece used in the house and probably the costliest one. Wouldn’t it be great if you could just make a bed of your own, without having to spend many bucks for buying one? So I am here sharing a great tutorial to help you to build a nice comfy platform bed that you can use anywhere in the house.
This is definitely going to be one of the easiest woodworking projects you’ll be reading about today. So why not just get started? The tutorial link is given below. Just do exactly what they are saying in the tutorial and you will end up making a beautiful wooden doormat just like the one in the image above. They are using pine wood to build this doormat. You can choose any wood material that best suits your budget.
With an orbital sander and good sandpaper you can smooth wood evenly and easily with first-class results. When flush-sanding solid edge-banding, draw a squiggly line across the joint before sanding. The edge-banding will be slightly proud of the plywood veneer, so the pencil marks provide a visual aid to make sure that you’re sanding flat, and that you don’t sand through the plywood’s veneer. As you go, you can also test for a smooth, level transition by gently scraping your fingernails against the transition. If it’s smooth, your fingers will not catch on the seam between the two pieces
I could write a whole post on wood species as each species has unique characteristics and traits. But, one of the most common types of wood used in DIY projects and furniture building is pine wood (a softwood). Pine is an affordable and readily available option at your local home improvement store and it comes in many sizes. I highly recommend using pine for beginner woodworking projects. Then, as you improve your skill, try working with some different wood species!
Some woodworkers obtain their skills by taking courses at technical schools or community colleges. Others attend universities that offer training in wood technology, furniture manufacturing, wood engineering, and production management. These programs prepare students for jobs in production, supervision, engineering, and management, and are becoming increasingly important as woodworking technology advances.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Lacking a jointer? Use reader Court Kites’ awesome tip to create perfectly matched glue joints on wavy or bowed board edges. Lay the boards on a flat surface, then clamp them across the middle with a bar clamp. Lay two 8-in. long by 1-3/4 in. wide scrap boards across each end and screw them in with four 1-1/4 in. long screws, two per board. Keep the screws well away from your future cutting line!
With an orbital sander and good sandpaper you can smooth wood evenly and easily with first-class results. When flush-sanding solid edge-banding, draw a squiggly line across the joint before sanding. The edge-banding will be slightly proud of the plywood veneer, so the pencil marks provide a visual aid to make sure that you’re sanding flat, and that you don’t sand through the plywood’s veneer. As you go, you can also test for a smooth, level transition by gently scraping your fingernails against the transition. If it’s smooth, your fingers will not catch on the seam between the two pieces

This simple jig makes laying out circles a breeze. Drill a 1/8-in. hole through every inch mark on a ruler or yard-stick. To draw a circle, place a pin through the number “1” into the center of your board. Add 1 in. to the radius of the circle you wish to draw, and insert a pencil into this number. Using the pin as a pivot, rotate the pencil to mark the circle. — Edwin Constantino. How to Cut Curves in Wood
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!
My planer blasts shavings all over the shop floor. I decided to make my own dust chute from 4-in. PVC sewer pipe (which has thinner walls than regular Schedule 40 pipe) and a couple caps. I cut a slit in the pipe and used a heat gun to soften the plastic. That allowed me to open the slit. (Heating PVC releases fumes; ventilation is critical.) I then drilled holes in the flap and screwed it to the planer housing. Finally, I cut a 2-1/2- in. hole in one of the end caps to accept my shop vacuum hose. Works great! — Luis Arce. Here’s what else you can do with PVC pipe.
The tutorial that I am sharing here was written by someone who built this pallet art just to improve the value of a property they wanted to sell fast and they succeed in it. So you can imagine how wonderful this item must look like. I am assuming you do not just want to make this beautiful pallet art so that you can also sell your property easily. Well, whatever your reasons are, this beauty is able to attract anyone who visits your house.
Instead of using a container to mix a small amount of epoxy, just make a mixing surface on your workbench using painters tape. Simply lay down strips, overlapping the edges so the epoxy doesn’t get on your bench. When you’re done, peel off the tape and throw it away. This mixing surface will work for more than just epoxy, you can use it for wood glue or any other material you need easy access to while working on a project. 

woodworking projects

×